Trov

How are you guys' temps & fan noise? Does the fan speed max out after a few minutes of a 3D game or does it stay at about mid level? I think that would make T2000 MaxQ or T1000 much more suitable. Do you have more details on your T2000 Max-Q card? Was it an HP card with the funny corner or something else?

I figure an M6800 would cope with the thermals a lot better since the heatsinks have a lot more heatpipes going around.

Hello, I wanted to share my success of upgrading an M4800's GPU to a Quadro T2000 I happened across a listing that was selling one for $180, which seems to be fairly cheap considering this is effectively an MXM A form factor GTX 1650. I was surprised it is offered in the MXM A size; as normally one would see a Quadro T1000 instead. This card is from I believe an HP Z2 Mini G5, and there is also a Quadro T1000 from the same machine, with the same non-standard board shape. More on that below. About The Card Not only is there a protrusion in the top right corner, it is slightly wider than a standard MXM A card by a couple mm. The back; unfortunately there are some SMD components blocking the "X" shaped attachment plate for the heatsink. I do not know how the heatsink attaches in the HP Z2 Mini; it must sit on some standoffs or something. Installation There are 3 concerns for installation: -The card being slightly wider -The top right protrusion -Components on the back blocking the possibility of an "X brace" heatsink attachment plate. Thankfully, nothing in the M4800's frame or screw posts blocks the card from being inserted. The only thing stopping it are the corners of the MXM slot intersecting with the T2000's wider body. The slot corners can easily be cut away with an exacto knife. This shouldn't pose much if any danger of damaging the MXM slot itself since you are just cutting plastic on a metal tab away from any of the connector pins. After cutting the corners of the slot, the card lowered down onto the screw posts. One should not worry about performing this permanent alteration; normal MXM cards will still slot in just fine after doing this. The next challenge is the corner protrusion. This doesn't cause any issue until you attempt to place the top bezel and keyboard back on. It turns out the speaker assembly would intersect with it. However, the part that intersects is just a hollow plastic chamber that can be cut away with an exacto knife without damaging the speaker itself. This may affect the sound quality but the sound quality was dire enough beforehand that I don't notice any meaningful difference. And lastly, the heatsink. Since there is no way to put the X-Brace on the back that the heatsink screws into, I had to use some nuts instead. Since there is no reinforcement on the back, I recommend avoiding tightening the 4 heatsink screws too tight. Also, you must install the heatsink before slotting in the GPU since you won't have much of a way to hold the nuts in place before screwing in. This means having to pull the whole motherboard out of the bottom case to insert the card, then putting it back. This isn't much extra work though, it's only a couple more screws than you already had out to get there in the first place. I had the Nvidia heatsink; it seems to be the correct distance for this card, I screwed the heatsink in without paste as a test and saw no daylight come through between the GPU die and the heatsink surface. VBIOS & Drivers I didn't need to touch the VBIOS. The laptop happily booted into Windows without any change (other than resetting CMOS) directly after putting in the T2000. The Nvidia installer would not detect the card. However, using Device Manager, selecting the GPU and selecting "Update Drivers" and then "Have Disk" and navigating to the Nvidia installer extraction folder and manually selecting the .inf worked. No changes were made to any .inf files. After a reboot Nvidia Control Panel was installed and the card was ready for running. Performance & Thermals On the desktop, the card idles at 43C, though I think Chrome was open with a good number of tabs. Here is Time Spy results, paired with i7-4900MQ: Conclusion The main downside is the card gets pretty hot at load, reaching 85C. After a few minutes of gaming, the M4800 will kick into maximum jet engine fan speed. It's not much of a wonder why, the card is rated as 60W TDP and the HP Z2 Mini's GPU heatsink is probably a good 2 or 3x the size of the GPU heatsink in the M4800. However, I did compare this thermal performance to my newer Precision 5540 that came with a T2000 built-in; and I noticed that laptop allows the GPU to go all the way up to 95C and thus the TimeSpy performance on that laptop throttled down to the 3100s. So, you might be able to get away with manually keeping your M4800 fans at Medium speed to keep the noise down at the cost of thermal throttling. It would be nice to be able to lower the power limit of the card to perhaps turn it into something akin to T2000 Max-Q, but unfortunately the VBIOS locks everything down, and MSI Afterburner cannot change any settings at all of this card. Therefore, the Quadro T1000 may be a better fit. I expect a T1000 from an HP Z2 Mini will work with all of the same steps as above, and stay below 70-75C according to a Youtube video I saw of someone putting a T1000 in his M4800. This HP T1000 may in the coming months be a far more accessible T1000 than the ADLINK ones that rarely pop up on Ebay. I did not test any external outputs; it is likely the GPU won't work in dedicated GPU mode. With Optimus mode, internal display works as you can see in the photos. This is quite a potent upgrade; games such as Doom Eternal run very well. This still isn't the end of the line for this laptop I suspect, as the RTX A2000 is being made in the MXM A form factor. In a few years those will probably be much more plentiful on the used market.