Maro97 Posted October 23 Author Posted October 23 On 9/30/2026 at 8:31 AM, Maro97 said: The two VRAM chips that are most likely faulty are C0 and D1, because they were close to the damaged area. The remaining low error counts are probably just signal interference, meaning “error ghosting.” I think there is still a good chance the card can be repaired. Finally! 🎉 I managed to repair an RTX 3080 graphics card that was about to end up in the trash, with a total repair cost of less than $80! Two traces between D1 and C0, which connect to the GPU, were broken. I repaired the GPU by performing a reballing, and the card came back to life! Many people told me to throw it away, that the card was dead, and that I should just buy a new one, especially with prices being ridiculously high. I actually bought another card on eBay from the same seller I had purchased the original one from, only to discover that it was faulty too. I ended up returning it to the seller. That experience made me even more determined to stick with my original card, as long as the GPU was still outputting data and the problem was somewhere on the PCB. What I learned from this journey: Never give up! 💪 Make the most of every repair video you watch, learn from every experience, and keep trying. All those graphics card repair videos I watched turned out to be incredibly valuable in bringing this card back to life. Sometimes, a little patience, knowledge, and persistence can save a GPU that everyone else has already given up on! 🔧🔥 1
Maro97 Posted 8 hours ago Author Posted 8 hours ago This is the end .. the issue is back .. The journey ended with me buying another card. There were no other solutions.
Developer79 Posted 7 hours ago Posted 7 hours ago Hi, Too bad, Maro, that the card got damaged. Normally, that shouldn't happen. It really shouldn't happen if you use the screws with washers. Did you manage to fix the graphics card!? I didn't read the whole thread, but I hope everything's working again. Greetings from Germany!
Maro97 Posted 4 hours ago Author Posted 4 hours ago 2 hours ago, Developer79 said: Hi, Too bad, Maro, that the card got damaged. Normally, that shouldn't happen. It really shouldn't happen if you use the screws with washers. Did you manage to fix the graphics card!? I didn't read the whole thread, but I hope everything's working again. Greetings from Germany! Hi, thanks for your message. Here is what I did: I removed the short caused by the screw penetrating the PCB surface: I scraped off the burnt layer and soldered the cut traces near D1 and C0. The card worked but showed VRAM artifacts, so I replaced the 2 VRAM chips with new ones of the same type. The card then worked normally and the line artifacts on the screen were gone. But under load, when the card reaches about 62°C, green squares appear, the card freezes, and RX/TX in GPU-Z stop updating. Finally, I reballed the GPU core and all the VRAM chips. The card worked very well and ran under load for 6 hours. Then I turned it off, and after 7 hours I started it again to check the solder balls after they had contracted and expanded. The problem came back. So I've ordered another RTX 3080 card and I'm done with this one. But I want to make sure the adapter itself is fine. When I tighten the screws and nuts to the right torque, I want the GPU surface to stay completely level, with no slight bowing. How can I check that?
Maro97 Posted 3 hours ago Author Posted 3 hours ago 3 hours ago, Developer79 said: Hi, Too bad, Maro, that the card got damaged. Normally, that shouldn't happen. It really shouldn't happen if you use the screws with washers. Did you manage to fix the graphics card!? I didn't read the whole thread, but I hope everything's working again. Greetings from Germany! Hi, thanks for your message. Here is what I did: I removed the short caused by the screw penetrating the PCB surface: I scraped off the burnt layer and soldered the cut traces near D1 and C0. The card worked but showed VRAM artifacts, so I replaced the 2 VRAM chips with new ones of the same type. The card then worked normally and the line artifacts on the screen were gone. But under load, when the card reaches about 62°C, green squares appear, the card freezes, and RX/TX in GPU-Z stop updating. Finally, I reballed the GPU core and all the VRAM chips. The card worked very well and ran under load for 6 hours. Then I turned it off, and after 7 hours I started it again to check the solder balls after they had contracted and expanded. The problem came back. So I've ordered another RTX 3080 card and I'm done with this one. But I want to make sure the adapter itself is fine. When I tighten the screws and nuts to the right torque, I want the GPU surface to stay completely level, with no slight bowing. How can I check that? What is the correct way to install the washers on the screw: on top of the heatsink's mounting hole, or under it (on the card side)?
Developer79 Posted 3 hours ago Posted 3 hours ago 35 minutes ago, Maro97 said: Hi, thanks for your message. Here is what I did: I removed the short caused by the screw penetrating the PCB surface: I scraped off the burnt layer and soldered the cut traces near D1 and C0. The card worked but showed VRAM artifacts, so I replaced the 2 VRAM chips with new ones of the same type. The card then worked normally and the line artifacts on the screen were gone. But under load, when the card reaches about 62°C, green squares appear, the card freezes, and RX/TX in GPU-Z stop updating. Finally, I reballed the GPU core and all the VRAM chips. The card worked very well and ran under load for 6 hours. Then I turned it off, and after 7 hours I started it again to check the solder balls after they had contracted and expanded. The problem came back. So I've ordered another RTX 3080 card and I'm done with this one. But I want to make sure the adapter itself is fine. When I tighten the screws and nuts to the right torque, I want the GPU surface to stay completely level, with no slight bowing. How can I check that? 23 minutes ago, Maro97 said: Hi, thanks for your message. Here is what I did: I removed the short caused by the screw penetrating the PCB surface: I scraped off the burnt layer and soldered the cut traces near D1 and C0. The card worked but showed VRAM artifacts, so I replaced the 2 VRAM chips with new ones of the same type. The card then worked normally and the line artifacts on the screen were gone. But under load, when the card reaches about 62°C, green squares appear, the card freezes, and RX/TX in GPU-Z stop updating. Finally, I reballed the GPU core and all the VRAM chips. The card worked very well and ran under load for 6 hours. Then I turned it off, and after 7 hours I started it again to check the solder balls after they had contracted and expanded. The problem came back. So I've ordered another RTX 3080 card and I'm done with this one. But I want to make sure the adapter itself is fine. When I tighten the screws and nuts to the right torque, I want the GPU surface to stay completely level, with no slight bowing. How can I check that? What is the correct way to install the washers on the screw: on top of the heatsink's mounting hole, or under it (on the card side)? Too bad the card broke! I always included washers with the adapters so that exactly this kind of thing couldn't happen. That was a fundamental aspect of my design. I also always recommended using thick adhesive tape to prevent damage to the PCB! If you pre-assemble the card while it’s still disassembled, you’ll see that the screw can’t make contact with the PCB and won’t cause any damage! That’s always included in my instructions 🙂 I hope everything works again now! Best regrads Ralf
Maro97 Posted 2 hours ago Author Posted 2 hours ago 1 hour ago, Developer79 said: Too bad the card broke! I always included washers with the adapters so that exactly this kind of thing couldn't happen. That was a fundamental aspect of my design. I also always recommended using thick adhesive tape to prevent damage to the PCB! If you pre-assemble the card while it’s still disassembled, you’ll see that the screw can’t make contact with the PCB and won’t cause any damage! That’s always included in my instructions 🙂 I hope everything works again now! Best regrads Ralf understand all of that now. My question is only about the washer position: should the washer go on top of the screw entry hole on the heatsink (under the screw head), or should it be threaded onto the screw after it passes through the heatsink hole, sitting between the heatsink hole and the X-bracket hole?
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now