johnksss

Not sure how he could kill that particular board with integrated graphics or something like a cmos reset to reset that dedicated gpu setting back to auto. Or maybe I missed something?

Yes, this I know and why I could not hold on to it. To many negatives that out weigh the positives. Still waiting for people to post on ocn with scores that come remotely close to @tps3443 .

That is about where my curve was for SP 101, but it did run 6.0Ghz on all P cores.

All I know is, they crack me up. I bet a Million to one, not one of those people are turning themselves in for defrauding the system in other more serious ways. And the same people claiming stuff just magically broke and think they should get a refund.🤣

Well mine wont even boot my stock 8400 ram, so that is an automatic no go, return to store.

Don't let the return police hear you....

We actual had some USA chips, but one person was saying the good ones were made in Israel so we got those ones.... I guess that was not the case.😄 Edit: Ordered the 100x100 0.1MM version

Mine says we have 1 left, but I'm not sure I want to waste time testing it..... If it's the USA version, maybe. As this one is from Israel.

The like is for the link to the foil. I take it that is 0.1MM? All is well, just been a bit busy with work and life in general. Haven't had time to sit and concentrate on the forums in a while. Plus a little gaming on the side as well. 🙂 Hey bro, good to see you as well.

Where did you get those from?

I will say this. It was able to run 6.0/4.7, but with really crappy results. I did not take the time to even record the scores. I was seriously temped to just take it back without opening, but curiosity got the better of me. As long as they have no issue taking it back, then checking should be ok. I would not even take the time to waste valuable paste though as temps are not going to change that curve. Once you see it's worth your time....then use the good stuff. Personal opinion only. Technically if you have a beefy heat sink sitting around you could hold that on it and boot to bios. Edit: Sorry, that was with me turning on the chiller to see if it could do 4.8E cores and 6.0 P cores.

Yep! and @Falkentyne went a total of 3 times today if I'm not mistaken.

Yes, the SP can be jacked up, but that voltage curve does not change though. lol

Everything is good, just going in a million directions and can't seem to stay planted on just 1 thing.😆 On the first bios it showed up as SP84, then on the flash it showed up as 101, but that VF is horrible. And I almost turned in my 13900KS SP112, but thought better of it! Also this chip wont boot my stock 8400's while my 13900KS does it with no trouble.

Hung out with brother @Falkentyne and Amaire from OCN at MC this morning. Here is mine which I wont be keeping.

So guys.... Interesting story. I have been playing Starfield for the past week or so now and my computer started just randomly shutting off. Made me have to go back and do certain parts of missions over and over again because I did not do a quick save. No over clocking just running off of two 360MM rad's and no chiller, but temps where not the issue. As I found out when running MSI Afterburner and Hwinfo monitors during gaming. I noticed that my 12vhpwr power was dropping to 11.3V then the computer would shut off. I checked the tips of both sides of cable and not even luke warm. I was thinking it was the power supply and that I might need to replace it under warranty, but that wasn't it either. When I unplugged both ends of the cable and replunged it back in, the voltage when back up to 12.1 volts during gaming. Not sure what the hell was going on, but I was like WTH is wrong with this POS. 😂. Turns out that from time to time one may need to unplug and re plug the cable back in from the power supply side. (as I swap between two 4090's.) Also NorthridgeFix was unable to find any issue with a Zotac 4090 I had. This card runs, but seems to cut out on video from time to time. But at the time, I never unplugged the cable from the PSU side so maybe I'll test that card again today. @tps3443I also asked for you about the gpu swap and he doesn't do that sort of thing. Says there are to many things that could go wrong so he doesn't do that. Edit: So Zotac 4090 seems to be holding at 11.9V and not cutting out nor dropping lower. I wonder if that was the issue....

I break it out on special occasions.😁 He was working on a video for soldering pins back on a 5900 AMD CPU. 😲

I haven't did that one yet, I was trying to figure out why I couldn't run the GPU test at first. Dropped off a project with Alex today...

Thanks. All is well on the western front.🙂

Here is my run on this...

It will be different for each person depending on PSU/wires/GPU I suspect. As long as you are no where near that 11.7 range. Which seems to indicate a serious voltage issue. One created by bad PSU or very bad contact. This needs to be checked under load.

one sec

Well, I seen where some people are using Hwinfo with the alarm to monitor the voltage on the rail. So I added that to mine as well.

All I can say is I do not check mine at all. I unplug it to swap things around then plug it back in. Every time I hear the click and that has been good enough for me. I do not tug or move or play with it. If it burns it burns. Although I can clearly see mine though 100% of the time. And looking at his pictures you can see where it was not pushed all the way end. I would delete those pictures when saying I plugged it in all the way.... just saying. Wait! he did delete them. 🤦‍♂️😂 Please tell me @Papusan screen shotted that one!!!! Wait! one is there, but the other two that show it really well are gone. Not sure if it's possible, but to correct this issue they would need to disable their "high tech" security feature.(Cable Sense) as the 8 pin connectors do not have this so when those cables are not plugged in fully the card does not even power on. The Kingpin cards will tell you which plug is either not working or not plugged in. Depending on how you look at it. (Just my opinion) Damn, this rash of 6 to 7 month card failures has me seeing double. Case 1 shows the line as well as case number 2. Case 2 has 5 pictures while case 1 has the 3.🤦‍♂️ User error on me!

Ah, okay. Mine is also free, but like you mentioned. All 4 of mine are covered in the sheath all the way to the PSU. Also to add.. All terminals seem to be pretty sturdy and no bent or out of place pins on the card itself.