Mr. Fox

https://hwbot.org/submission/4981077_ https://hwbot.org/submission/4981094_

I think mine is a good example of that based on the fact that a delid didn't improve the temps as much as other examples we have seen, but those where the delid made a bigger difference seem to have run hotter than mine did before a delid. But, some of that may also have been related to my cooling setup as well. The examples seen on YouTube were using systems with more mainstream cooling setups with an AIO or a much smaller custom loop. Without the chiller running, my system normalizes temperatures within about 3 to 5 minutes and the only time it changes up or down is dependent on the ambient temperatures. Those stress test comparisons I showed were at the temperature shown within about 3 or 4 minutes and whether I let the stress test run for 4 minutes or 40 minutes was irrelevant. The temperatures reached a certain point and then remained flat, both before and after delid. The stress wasn't able to overcome the cooling system.

Part of it could also be some variance in the quality of the solder job attaching the IHS to the die. You could have a CPU wih better SP rating that runs hotter and is more of a power pig than a lower SP rating silicon sample.

OK, well... I did that washer mod thing that has been talked about relating to the 12th Gen ILM crushing the CPU into a banana shape. I used some M4 1mm thick nylon washers, and it did lower the temps a bit, even after a delid with the copper IHS. I started the stress test and left at 3 minutes in to run to the store, and got back after the test had run for a total of 40 minutes. I put this into a side-by-side for ease of viewing. It was certainly easier to latch with the washers in there. It was so tight before that it almost felt like something is going to get broken before you can latch it down.

Yeah, just extra garbage payload that comes along with newer tech adding things that add no value, and lying about them not being compatible with W7. I have Treexy and it is reputable. It works kind of like Snappy Driver Installer (also a good tool) but Treexy has other features. Both are useful for people that find driver hunting to be intimidating or boring. But, neither one will make the anti-7 NeoNazi 10+ drivers work on W7 that have to be modded. I'd pay a nice amount of money if someone would develop an automatic driver modding tool. It would probably have to be Russian or Chinese to escape malicious litigation from the creeps at Intel, NVIDIA, AMD and Micro$lop and their bogus DMCA violation suits. I am pretty good at driver modding as long as it only involves the INF. Where it gets into modding the SYS files with a hex editor, it's above my pay grade. I wish I knew how and I'd teach others how to use that knowledge and give a double-fisted nasty-finger salute to the smelly Kontrol_Klown_Klan.

After tinkering with some of my BIOS settings, an "Unkown Device" suddenly appeared in Device Manager on Windows 7. This driver that I modded will fix that if the unknown device HWID is ACPI\INTC1056. It is not important in the grand scheme of things, but I hate having things in Device Manager remain unresolved. Now I am back to everything being as it should be in Device Manager with everything recognized and working normally as long as the silly WiFi 6/BT crap is disabled in the BIOS. https://mega.nz/file/AZ91QSCT#GHXoZS9zeP4V1Uf8Ngp7Nsz6kP-DRITzMEpO3id7Sao

That's a good PSU. I have the Bronze version of it in Banshee.

Hey bro, it's an ordinary EPS connection that all modern PSUs support. Each EPS cable has an 8-pin connector that is split in a 4+4 male plug on the motherboard end. To use the supplemental 4-pin power (optional) you simply plug in half of a second EPS cable. In concept it works the same as the 6+2 VGA power connection, where you omit the 2-pin connection on a GPU that only has a 6-pin power connection. You must connect at least one 8-pin (4+4) EPS cable to the motherboard. The extra 4-pin connection is for higher power demands like severe overclocking. It spreads the load out to reduce heat when all of the load has to be funneled through a single EPS cable. All PSUs of a decent capacity come with at least two CPU EPS cables. Sadly, most of the reasonably-price PSU custom cable kits and generic cable extension kits include only one EPS cable and you usually end up needing to waste money on a second kit just to get the second EPS cable.

I almost got excited about that for a minute, then I realized it was an aftermarket ILM replacement and not a bare die frame. Bummer.

It is actually gigabit, but since it is the only option available here that is fast enough for people that care about that the speed ends up less due to network congestion. It is still way better than the chintzy 20Mbps trash internet available from the one and only competitor available to me though.

The 7000D is huge, but seems small and light compared to the Level 20 XT. It is not as tall, but MUCH wider (fits 2 PSU side-by-side) and depth from front to back is 26 inches... enough to set two ATX mobos next to one another... insane. But, no lack of space. I can carry it with no problem, but if I had to go up and down stairs it would be a two-person job to avoid dropping it because there is not much to hold onto. Interesting that you had difficulty with cable management. The 5000D did not give me any challenges with that. There was enough space for everything to fit with no issues, but a little bit tight on the back side of the mobo tray. Not really any "extra" space though, and certainly not what I would categorize as "roomy" or excess space. My preference is definitely to have more space (at least 50% more) than what is actually needed. I hate the feeling of being cramped or having to carefully plan in order for everything to fit. (I hate puzzles too, LOL... they suck.)

Good, but nowhere near that good. But, it is the best I can get where I live. Everything else is slower.

It might be something with the delid tool not placing pressure in the ideal location. I am just glad it only scarred the top of the IHS and didn't damage the CPU. It is good that I ordered the copper IHS in the kit instead of only the delid tool by itself, otherwise I would have needed to stop and sand down the IHS before I could reassemble it. Since the stock IHS is ruined, I may as well go ahead and lap it and polish it at this point. The ONLY reason I ordered the copper IHS was to keep the stock IHS looking like new, so I'm somewhat perturbed by it for that reason. Otherwise, I would not care. My intent is to go bare die when the parts become available to do that.

Well, I got the delid done. Definite improvement, although not as amazing as I had hoped. My temps were already better than most I have seen, so that probably has something to do with it because there was less room for improvement. I have historically had better temps with the stock IHS than I have using a Copper IHS. Unfortunately, the delid tool caused damage to the stock IHS. In order to use it I will need to lap it to fix the damage, which sucks because the main reason to have an aftermarket IHS is to keep the stock one looking new. Lapping it would totally defeat the purpose for buying an aftermarket IHS. I am not sure if the IHS deformation is because the 12th Gen IHS is softer metal than prior generations, if it is because it takes more force to break the solder joint, or if the RockitCool delid tool isn't made correctly. Nothing in terms of user error could cause it because all you do it put it in the pocket and tighten the lid down snugly. I also heated the IHS to soften the solder.

I'm not really sure if it does or not. I can't really comment. I typically do not use any Windows UWP app thrash except in circumstances where the avoidance of them becomes impossible. Even then my use is generally limited to native/core filth like Settings and the DCH feces NVIDIA Control Panel. I will not even use those when another option is available, like legacy Control Panel, gpedit, regedit or NVIDIA Profile Inspector. UWP filth is always a last resort option for me.

Arrived a day earlier than expected.

I haven't looked at it and probably won't bother because I truly don't care what they do. But, the idea on face value raises the question of intelligent design and logic in developing an added layer of proprietary garbage. If adding a CAMM module takes space, and the only place anyone can buy a CAMM module is from Dell, and Dell doesn't make them readily accessible and inexpensive to purchase, it still leads back to questionable business practice and ulterior motives.

An interesting and conceptually similar issue noted over here... https://forums.extremehw.net/topic/2003-dells-new-laptop-features-proprietary-ddr5-module-wont-take-generic-ram/#comment-24960

Yes, that's a really nice sample you have there. Congrats, bro.

Nice... something special on Github for Winduhz 11 fanbois.

A new twist for story time for the kiddies...

It is unfortunate that Intel, AMD and NVIDIA can get away with crap variance in product quality like that. It's really messed up, maybe even immoral, that you could grab two processors from the same shelf at the same time, pay the same price for both, and end up with two such remarkably different experiences. Rather than calling binned CPUs a "KS" and selling them for more, they should sell the inferior products for less because they are inferior. But, that would be an honest way of running a business, and honesty is rare in the realm of technology. I finally took time to delid the 10900K in Banshee last night. I did not have time to tinker with bare die. This is just a delid with Liquid Pro on the die and KPX on top of the IHS. Maybe this weekend I will find some spare time to test the Supercool Computer direct die block that I have never used. Maybe not though. The 12th Gen delid kit will be here, so I will most likely burn my calories on that. Definitely worth it. It really amazes me that there are still people that think it doesn't help enough to bother. Excluding the 5950X as an exception, I have never seen an example where a delid brought so little improvement as to not matter. Results below are with the same BIOS settings. Ambient temps are 76-78°F (about 25°C). Before Delid: 15 minute stress test After Delid: +6 minutes longer stress test (21 minutes)

They only want the sheeple for customers. They are smart enough to recognize that the sheeple are their target audience. Shooting fish in a barrel isn't fishing, but you can harvest a lot more fish without any skill being required for success. Likewise, being bad doesn't mean that you're not smart. For example, I think it is pretty apparent that Satan is smart, he just uses what he knows for nefarious purposes.

I think your numbers are more accurate from a global view. The survey in the article I linked was a more limited sample, but the underlying message is similar... Windows 11 sucks and it is not being embraced. So, it's a good message regardless of whose numbers we are looking at. It's only a bad message if you are Micro$lop fanboy or a Kool-Aid drinker. I consider it a good thing to be glad whenever lousy products fail, because I don't want the companies that produce garbage to prosper.

I'm sure that if there were more zombie turdbooks in circulation the market share of Windows 11 would be higher than it is right now. I suspect there are quite a few kiddos out there that want what they can't have, even though what they want is garbage. The Smart ones will figure out how to get what they want through common bypasses, but the rest will just whine about it, LOL. They should all be glad that their machines don't qualify for the downgrade. Just one less thing that doesn't need to be manually blocked.