RTX 3080 in M18xR2? Should I do it? lol

[SuperMG]

3 hours ago, FrancoTecno said:

and about ZRT??? 

They are offline for weeks

[janepa]

On 9/8/2025 at 8:38 PM, SuperMG said:

Hello

 

 

I did this and it's in production 

 

 

Yes for the 3 pins, the reverse side will have some very thin layer of double-sided tape.

 

I added some shapes to the extremities so we can stick with some tape.

 

Won't short-circuit, can handle over 230C of ambient temperature.

 

That´s very good idea .Awesome. Maybe will be v2 version in future. 

[janepa]

On 9/10/2025 at 4:04 AM, TruenoG7 said:

Interesting contribution, could you describe what you actually did to convert your M18xR2 from LVDS to EDP? I would also like to know if that could also be done on the Alienware 18 (2015)?

 

Hi
Nothing special ,bad news of course is that my solution require some soldering expiriences. Basically add new lines from mxm connector where have Gpu DP-out pins to mux switch instead of old LVDS lines . Most important is known on which pins of Gpu is simply DP not advanced DP+ or DP++ ,because in this case the lcd have issue to catch up the high frequency signal as well. For example my chinese Gpu cards (RTX4090 X-VSION and RTX3070 16Gb PELADN) have both DP++ on DP_A,B and simply DP on DP_D, but my Adlink Quadro RTX5000 have DP++ on all DP ports. In this case is necesesary to add between mxm and lcd (retimer, repeater) . You can recognize it that lcd normally work untill install Gpu drivers. After that is black screen. This is not of EDID issues! Maybe ask for help user SuperMG to developing the flex cable to bridge lines from LVDS to DP_D right on MXM conn. for non soldering solutions.

I think that will working on Alienware 18 too.

[SuperMG]

1 hour ago, janepa said:

 

Hi
Nothing special ,bad news of course is that my solution require some soldering expiriences. Basically add new lines from mxm connector where have Gpu DP-out pins to mux switch instead of old LVDS lines . Most important is known on which pins of Gpu is simply DP not advanced DP+ or DP++ ,because in this case the lcd have issue to catch up the high frequency signal as well. For example my chinese Gpu cards (RTX4090 X-VSION and RTX3070 16Gb PELADN) have both DP++ on DP_A,B and simply DP on DP_D, but my Adlink Quadro RTX5000 have DP++ on all DP ports. In this case is necesesary to add between mxm and lcd (retimer, repeater) . You can recognize it that lcd normally work untill install Gpu drivers. After that is black screen. This is not of EDID issues! Maybe ask for help user SuperMG to developing the flex cable to bridge lines from LVDS to DP_D right on MXM conn. for non soldering solutions.

I think that will working on Alienware 18 too.

Hello.

 

Do you know where the eDP is on the X-VSION 4080/4090? I see eDP port on NVIDIA's control panel but I don't get it.

 

 

I don't get it on which port the EDP is? On port DP_E??? does that even make sense? Please let me know, X-VSION's datasheet shows eDP on DP_B...

 

My flex cable is just to enable the backlight pins back so we can have a display at the end. Most Turing to Ada are lacking the pins. Most of them have DP and eDP on DP_D

 

 

The picture I sent clearly shows how it works. I see no LVDS conversion. It just 3.3V to power the backlight pins, that's it.

[SuperMG]

@janepa

 

If you have an eDP laptop (DP_D eDP) with a MXM slot,

please try the mod by soldering pins 278/280 to pins 23,25 and 27 for the backlighting.

 

You'll see that your 4090, 3070 and RTX 5000 will work with the main screen. Try it please.