MaxxD
-
Posts
308 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by MaxxD
-
You will laugh, but I just turned on the zTecpc X170 and did not connect the mDP cable and the HDMI cable carefully (watching the lower sensors - I will test this later!) and the laptop display shows G-Sync / 144Hz again but the 150W GPU TDP max. 😄 The +15W GPU Boost is missing... I installed MSI AB but I didn't see the option to turn off the power limit there. (how is it available - I read that 15W Boost was available to someone) I tried nV Control Panel / 3D settings / Power management mode / Normal --> Maximum (but no change, 150W max. TDP)
-
Exactly. I haven't looked or tried that. 4K/120Hz was connected to the HDMI 2.1 port on the RTX 3090 card. 😉
-
Yes, 4K 60 is fine, but 4K 120 is not. HDMI port is only 2.0 and mPD 1.4 port. In the case of mDP 1.4 to HDMI 2.1, you should know 4K/120Hz, but you don't. (watched) There was a time when I looked at an external ThunderBolt 3 eGPU (Gigabyte Aorus Gaming Box RTX 3090) and it was capable of 4K/120Hz (the card already had HDMI 2.1 from the factory)
-
"Prema BIOS"
-
Yes! I am absolutely right. Unfortunately, I didn't even think of that, another (PCS) X170 has Macrium Reflect 😛 If there is nothing else, I can reset the system (because there is no reset point) or rather "reset" and that is faster (or not) But this HDMI problem also bothers me! I checked and there are 2 legs on each side that do not stand (only the end) and I would rather call them worn. Now I cleaned it with alcohol and scrubbed it with a small brush, I hope it was just a contact error...if not, then the HDMI connector must be replaced!🤔 VIDEO
-
Yes, I used DDU for the full driver deletion. I re put that driver with the NVClean program, but it is not complete because it does not have the specific 3080 card on your list...so it is not complete! BIOS was set to default at the beginning and left it. You know, when one day a little bit of something and everything starts to mix. Especially if you don't get from one to two, you only have one place. There is no worse!😁😑 You have to find a solution to this problem, otherwise the machine would just be a discarded money that wouldn't make happiness like that!🥺
-
I also had a G-Sync, but it disappeared...I played with HDMI 2.1 and MDP 1.4 ports and since then it hasn't, and this hdmi port is not very good on the laptop. 😩
-
By now, this is a bit much! 😩 All my respect is yours, seriously! ✌️ Then maybe I'll try it.😉
-
Now, with a direct DDU, I covered the NV driver (Full) and reinstalled it in reduced mode and no G-Sync. But I can't specify the card ID at NVClean because it's not in the list so I can't choose it. I rewrite the INF file in vain because the installation fails. Then what is the solution?🤗
-
Now I only use the laptop display and no G-Sync. There was a machine restart, no G-Sync. (this feature has disappeared) 😗
-
There was a G-Sync on the laptop display, but it disappeared!? How!?😄🙂
-
New 3DMark Bench 🙂 "Optimal" (Default) to CPU and GPU (mode) TimeSpy Normal or Extreme? 😛
-
Video I don't know how it is, but with HDMI 2.1 cable, the 4K 120Hz G-Sync (HDMI 2.1) had a G-Sync on TV, but the image blinks while connecting. MDP 1.4 to hdmi 2.1 cable is not g-sync, can it be because of the "bad" HDMI connector? It started again after a couple of blinking ... (Could be a contact error!?) 3DMark Steel Nomad test (no G-Sync, no 165W TDP...) mDP 1.4 port was used. Machine (my own display) has G-Sync I should see, there may be gpu boost (+15W) ???🤗😂
-
Thanks!🙏 I chose and left that time because it was not good when rewritten. Written at 7714 was not good, so the 7715 remained.💪 G-Sync and 165W TDP is OK! 😊
-
Yes! The picture also features blade fans of such density and that's why I dared to order it directly...but it was a big mistake! Aliexpress: LINK Seller only wrote back "new" 🤗 It's not! It comes from a demolished machine ... and not what is in the picture.
-
Unfortunately, I can't do it all the time because this hardware is not on the list, so it is not optional.😑 Thank you for you too! 😄
-
The fans I got the big scam! I beat the fool. Not new fans, but dismantled and exactly the same as the original! This is outrageous! 🤔
-
Unfortunately, you don't want to be good at all. BIOS set to Default. I also got a modified INF file, but not good when applying. I don't know what to do anymore...
-
Unfortunately, I don't know the operation to do all the time!😌 Complicated?🤗🤭
-
Do I make a default setting in BIOS? Do you think? 🤔😁
-
I thought it was going to go and no need to change. BIOS As I watched it is good, you will change.🤔 This bios is much better than the factory closed... ☝️✌️😉
-
What should you turn on to make the Prema BIOS X170SM-G machine smoothly carry the RTX 3080 card? I haven't looked at the bios yet, but I'll look over it! 😃 I fixed the zTecpc machine today. Cooling trash, gpu (RTX 2080 Super) trash, screws trash...there are a few more things. The transport company could be football for the package ... and it was sent as a fragile package and insurance. It received aqueous cooling and I9-10900K was put in. Memory is also 2x16GB. SSD is 4x2tb and then...3080 I hope you will go under a basic Prema BIOS!
-
Someone made a huge mistake to use this washer screw solution because he broke the gpu chip corner. It is outrageous that anyone does it!🤔 zTecpc Technical Support confirmed that they also fitted the Clevo X170SM-G version with a spring factory screw.😔
-
As far as I know, the Prema zTecpc X170 version handles the RTX 3080 MXM card without any problems. I hope I get there to try this. ✌️😋
-
I completely agree!☝️ On one machine, the obsidian remains fully and the Control panel. Taking advantage of BIOS on a Prema machine, the full fine tuning is the target water cooling. The only problem now is that during the delivery, the zTecpc X170 is the fixed screw (non spring) heatsink fixation with one heel of 2080 Super) is broken and the other corner is cracked, so it cannot be used.😔 /I made the pictures myself with the help of a digital microscope/ The broken corner is visible to the naked eye! I'm a repair technician, so it wasn't difficult to find out the error. The GPU chip is available with eBay and can be replaced with a fineplacer or free hand. (It's not worth it for me!)😌 I have RTX 3080 cards, but I need to transfer the whole water to cool from the other machine so I can use the zTecpc machine. CPU, RAM, SSD, will be loaded, the PCS X170 will also be appropriate with the I5 CPU with RTX 2080 Super. It's good that the PCS machine is not a basic RTX 20xx card.🙂 This will not be a small operation and it is planned next week. Did others have a similar problem with zTecpc X170 during the (long, nearly 2,000 kilometers) transport? 🤔
